HDMI TWP FLAT CABLE
Optionally supports output of Dolby True HD and DTS-HD Master Audio streams for external decoding by AV receivers.( TrueHD and DTS-HD are lossless audio codec formats used on Bly-ray Discs and HD DVDs . )
Specifications
Optionally supports output of Dolby True HD and DTS-HD Master Audio streams for external decoding by AV receivers.( TrueHD and DTS-HD are lossless audio codec formats used on Bly-ray Discs and HD DVDs . )
1. Construction
Differential signal
Control and other signal
Conductor
Material
-
Silver coated annealed copper wire
Tin coated annealed copper wire
Diameter
mm
Approx. 0.254 (Size:30AWG)
Insulation
Material
-
Foam PE
PE
Color
-
White , Red
Green , White , Red
Diameter
mm
Approx. 0.7
Approx. 0.5
Twisting
Composition
-
Two insulated conductors (White-wire and Red-wire) shall be uniformly twisted together.
-
Shield
Composition
4 sets of twisted pairs, 4 sets of drain lines and 7 sets of control lines are arranged in alignment as shown in the attached drawing and wrapped by a shield tape. Shield tapes are also inserted between the twisted pairs, separating each pair.
There should not be gaps in the wrapping shield tape and in the shield tapes between the twisted pairs.
Also, both the ends of the wrapping shield should be glued without gaps, and the edged part glued should be neatly cut without forming a projection.
Kind
-
For outsides : Aluminum Polyester Laminating Tape
For inside : Aluminum Polyester Aluminum Laminating Tape
Thickness
mm
For outsides : 0.025 (Al : 0.006)
For inside : 0.03 (Al : 0.006)
Drain
Material
-
Tin coated annealed copper wire
Diameter
mm
Approx. 0.254 (Size : 30AWG)
Jacket
Material
-
PVC
Color
-
Black
Thickness
mm
Nom. 0.5
Overall diameter
mm
H*W=1.85 ´ 11.5 ( ± 0.1 )
Marking
E54979 AWM 20276 80℃ 30V VW-1 TATUNG
- HDMI
2. Rating
Rating Voltage
V
30
Rating Temperature
℃
80
3. Performance
Electrical Requirements
Conductor resistance
Ω/km
Max.361 ( at 20℃ )
Dielectric strength
V-min
To withstand 300 Volts R.M.S. for one minute.
(Between all interconnected conductors, and all the
interconnected shields.)
Insulation resistance
(Between conductor and earth)
MΩkm
Min. 10
This measurement shall be made with 150 volts D.C. after steady electrification for one minute.
(During the tests, remaining conductors shall be connected to earth.)
Differential impedance
Ω
Cable Area 100±10
Connector Area 100±15
Delay*
ns/m
Max. 5.05
Inter-Pair Skew*
ns
Max. 2.42
Intra-Pair Skew*
ps
Max. 151
Far-end crosstalk*
dB
Max. -26 dB (f=300k～5000MHz)
Insertion Loss*
dB
Min. - 8 dB (f=300k～825MHz)
Min. -21 dB (f=825M～2475MHz)
Min. -30 dB (f=2475M～4125MHz)
Capacitance**
pF
Max. 700
*Differential signal line
**Between Pin No.15 to No.17 and No.16 to No.17
4. Cable FLAME TEST
To conform to UL 1581 VW-1 combustion test.
5. RoHS Regulation
Material name
Rated value
Cadmium and Cadmium Compounds
75ppm
Hexavalent Chromium Compounds
1000ppm
Lead and Lead Compounds
300ppm
Mercury and Mercury Compounds
1000ppm
PBB (Polybrominated Biphenyls)
1000ppm
PBDE（Polybrominated Diphenyl Ethers）
1000ppm
6. Cable Wire Assignment
Pin
Color
Cable Function
1
Red
TMDS Data 2+
3
White
Green
2
Drain
TMDS Data 2 Shield
4
Red
TMDS Data 1+
6
White
TMDS Data 1-
5
Drain
TMDS Data 1 Shield
7
Red
TMDS Data 1 Shield
9
Red
TMDS Data 0-
8
Drain
TMDS Data 0 Shield
10
Red
TMDS Data Clock+
12
White
TMDS Data Clock-
11
Drain
TMDS Clock Shield
13
Green
CEC
14
Red
Reserved（N.C. on device）
15
White
SCL
16
Green
SDA
17
Red
DDC/CEC Ground
18
Red
+5V Power
19
White
+5V Power
相關產品
-
Cat.5 UTP 24AWG 25P、50P、100P
LAN CABLE is suitable for data transmission on Local Area Network , especially for computer, video or perfect audio. Specifications 1. Wire Construction： Pair Wire Arrangement Pair Wire Arrangement 1 P Blue ´ White 14 P Brown ´ Black 2 P Orange ´ White 15 P Gray ´ Black 3 P Green ´ White 16 P Blue ´ Yellow 4 P Brown ´ White 17 P Orange ´ Yellow 5 P Gray ´ White 18 P Green ´ Yellow 6 P Blue ´ Red 19 P Brown ´ Yellow 7 P Orange ´ Red 20 P Gray ´ Yellow 8 P Green ´ Red 21 P Blue ´ Violet 9 P Brown ´ Red 22 P Orange ´ Violet 10 P Gray ´ Red 23 P Green ´ Violet 11 P Blue ´ Black 24 P Brown ´ Violet 12 P Orange ´ Black 25 P Gray ´ Violet 13 P Green ´ Black 25P: with no color tape 50P: 1P~25P unit is wrapped with one white tape and one blue tape, 26P~50P unit with white and orange 100P:1P ~ 25P unit is wrapped with one white tape and one blue tape, 26P ~ 50P unit with white and orange, 51P ~ 75P unit with white and green 76P ~ 100P unit with white and brown. 2. Structure Item Specification Conductor Material Annealed Copper Construction 1 / 0.52 mm Diameter Approx. 0.52 mm Insulation Material HDPE Average Thickness Approx. 0.2 mm Diameter 0.92 ± 0.05 mm Twisted Refer to structure figure Assembly Arranged in accordance with the structure figure. Jacket Material PVC or LSOH Average Thickness Approx. 1.0 mm Diameter (25P) Approx. 14.0 mm Diameter (50P) Approx. 14.0 × 26.0 mm Diameter (100P) Approx. 31.0 mm 3. Electrical Characteristics: Comply with TIA/EIA-568-B.2 Standard. Item Electrical Characteristics of Cable Impedance ( 1 – 100 MHz) 100 ± 15 Ω Conductor Resistance ( 20℃ ) 9.38 Ω Per 100 m ( 328 ft ) Resistance Unbalance ( 20℃ ) Max. 5% Insulation Resistance ( 20℃ ) 1500M W - Km DC 500V (Between wire and ground) Dielectric strength DC 500V / 1min. or AC 350 V / 1min. Mutual Capacitance (1KHz) Max. 5.6 nF Per 100 m ( 328 ft ) Capacitance unbalance (1KHz) 330 pF Per 100 m ( 328 ft ) ( pair to ground) Delay Skew Max. 45 ns Per 100 m ( 328 ft ) Frequency Insertion Loss (dB/ 100m ) Max. Propagation Delay 0.772MHz 1.8 — 1 MHz 2.0 534 + 36/ √f (f：MHz) 4 MHz 4.1 8 MHz 5.8 10 MHz 6.5 16 MHz 8.2 20 MHz 9.3 25 MHz 10.4 31.25 MHz 11.7 62.5 MHz 17.0 100 MHz 22.0 Frequency NEXT (dB/ 100m ) Min. PSNEXT (dB/ 100m ) Min. ELFXT (dB/ 100m ) Min. PSELFXT (dB/ 100m ) Min. 0.772MHz 67.0 64.0 — — 1 MHz 65.3 62.3 63.8 60.8 4 MHz 56.3 53.3 51.7 48.7 8 MHz 51.8 48.8 45.7 42.7 10 MHz 50.3 47.3 43.8 40.8 16 MHz 47.3 44.4 39.7 36.7 20 MHz 45.8 42.8 37.7 34.7 25 MHz 44.3 41.3 35.8 32.8 31.25 MHz 42.9 39.9 33.9 30.9 62.5 MHz 36.4 35.4 27.8 24.6 100 MHz 35.3 32.3 23.8 20.8 Return Loss (dB/ 100m ) 1≦ f ＜10MHz RL≧ 20+5.0 log(f) 10≦ f ＜20MHz RL≧ 25
-
CAT5E-FTP-4P
LAN CABLE is suitable for data transmission on Local Area Network , especially for computer, video or perfect audio. Specifications 1. Wire Construction: Pair Wire Arrangement 1 P Blue ´ White / Blue Stripe 2 P Orange ´ White / Orange Stripe 3 P Green ´ White / Green Stripe 4 P Brown ´ White / Brown Stripe 2. Structure: Item Specification Conductor Material Annealed Copper Construction 1 / 0.54 mm Diameter 0.54 ± 0.005 mm Insulation Material HDPE Average Thickness 0.247 mm Diameter 1.03 ± 0.02 mm Twisted Refer to structure figure Assembly Arranged in accordance with the structure figure. Non-woven tape Approx. 0.2 mm in thick. Drain Wire Material Annealed Tinned Copper Construction 1 / 0.515 mm Al - Mylar Approx. 0.06mm in thick. (with Al side in) Jacket Material PVC or LSOH Average Thickness 0.6 mm Diameter 6.3 ± 0.2 mm Packing 305 m plywood drum in a box 3. Electrical Characteristics： Comply with TIA/EIA-568-B.2 Standard. Item Electrical Characteristics of Cable Impedance ( 1 – 100 MHz) 100 ± 15 Ω Conductor Resistance (20℃) 9.38 Ω Per 100 m (328 ft) Resistance Unbalance (20℃) Max. 5% Insulation Resistance (20℃) 1500MW - Km DC 500V (Between wire and ground) Dielectric strength DC 500V / 1min. or AC 350 V / 1min. Mutual Capacitance (1KHz) Max. 5.6 nF Per 100 m (328 ft) Capacitance unbalance (1KHz) 330 pF Per 100 m (328 ft) ( pair to ground) Delay Skew Max. 45 ns Per 100 m (328 ft) Frequency Insertion Loss (dB/100m) Max. Propagation Delay 0.772MHz 1.8 — 1 MHz 2.0 534 + 36/ √f (f：MHz) 4 MHz 4.1 8 MHz 5.8 10 MHz 6.5 16 MHz 8.2 20 MHz 9.3 25 MHz 10.4 31.25 MHz 11.7 62.5 MHz 17.0 100 MHz 22.0 Frequency NEXT (dB/100m) Min. PSNEXT (dB/100m) Min. ELFXT (dB/100m) Min. PSELFXT (dB/100m) Min. 0.772MHz 67.0 64.0 — — 1 MHz 65.3 62.3 63.8 60.8 4 MHz 56.3 53.3 51.7 48.7 8 MHz 51.8 48.8 45.7 42.7 10 MHz 50.3 47.3 43.8 40.8 16 MHz 47.3 44.4 39.7 36.7 20 MHz 45.8 42.8 37.7 34.7 25 MHz 44.3 41.3 35.8 32.8 31.25 MHz 42.9 39.9 33.9 30.9 62.5 MHz 36.4 35.4 27.8 24.6 100 MHz 35.3 32.3 23.8 20.8 Return Loss (dB/100m) 1≦ f ＜10MHz RL≧ 20+5.0 log(f) 10≦ f ＜20MHz RL≧ 25 20≦ f ＜100MHz RL≧ 25-7.0 log(f/20)
-
CAT5E-SFTP-4P
LAN CABLE is suitable for data transmission on Local Area Network , especially for computer, video or perfect audio. Specifications 1. Wire Construction: Pair Wire Arrangement 1 P Blue ´ White / Blue Stripe 2 P Orange ´ White / Orange Stripe 3 P Green ´ White / Green Stripe 4 P Brown ´ White / Brown Stripe 2. Structure: Item Specification Conductor Material Annealed Copper Construction 1 / 0.54 mm Diameter 0.54 ± 0.005 mm Insulation Material HDPE Average Thickness 0.247 mm Diameter 1.03 ± 0.02 mm Twisted Refer to structure figure Assembly Arranged in accordance with the structure figure. Non-woven tape Approx. 0.2 mm in thick. Al - Mylar Approx. 0.06mm in thick. (with Al side out) Braid Shield Material Annealed Tinned Copper Construction 24 / 8 / 0.12 mm Jacket Material PVC or LSOH Average Thickness 0.6 mm Diameter 6.9 ± 0.2 mm Packing 305 m plywood drum in a box 3. Electrical Characteristics: Comply with TIA/EIA-568-B.2 Standard. Item Electrical Characteristics of Cable Impedance (1 – 100 MHz) 100 ± 15 Ω Conductor Resistance (20℃) 9.38 Ω Per 100 m (328 ft) Resistance Unbalance (20℃) Max. 5% Insulation Resistance (20℃) 1500MW - Km DC 500V (Between wire and ground) Dielectric strength DC 500V / 1min. or AC 350 V / 1min. Mutual Capacitance (1KHz) Max. 5.6 nF Per 100 m (328 ft) Capacitance unbalance (1KHz) 330 pF Per 100 m (328 ft) ( pair to ground) Delay Skew Max. 45 ns Per 100 m (328 ft) Frequency Insertion Loss (dB/100m) Max. Propagation Delay 0.772MHz 1.8 — 1 MHz 2.0 534 + 36/ √f (f：MHz) 4 MHz 4.1 8 MHz 5.8 10 MHz 6.5 16 MHz 8.2 20 MHz 9.3 25 MHz 10.4 31.25 MHz 11.7 62.5 MHz 17.0 100 MHz 22.0 Frequency NEXT (dB/100m) Min. PSNEXT (dB/100m) Min. ELFXT (dB/100m) Min. PSELFXT (dB/100m) Min. 0.772MHz 67.0 64.0 — — 1 MHz 65.3 62.3 63.8 60.8 4 MHz 56.3 53.3 51.7 48.7 8 MHz 51.8 48.8 45.7 42.7 10 MHz 50.3 47.3 43.8 40.8 16 MHz 47.3 44.4 39.7 36.7 20 MHz 45.8 42.8 37.7 34.7 25 MHz 44.3 41.3 35.8 32.8 31.25 MHz 42.9 39.9 33.9 30.9 62.5 MHz 36.4 35.4 27.8 24.6 100 MHz 35.3 32.3 23.8 20.8 Return Loss (dB/100m) 1≦ f ＜10MHz RL≧ 20+5.0 log(f) 10≦ f ＜20MHz RL≧ 25 20≦ f ＜100MHz RL≧ 25-7.0 log(f/20)
-
CAT5E-UTP-4P
LAN CABLE is suitable for data transmission on Local Area Network , especially for computer, video or perfect audio. Specifications1. Wire: Pair No. Color 1P Blue ´ White/Blue Stripe 2P Orange ´ White/Orange Stripe 3P Green ´ White/Green Stripe 4P Brown ´ White/Brown Stripe 2. Specification: Conductor Material Copper Wire Structure 1 / 0.515 ± 0.007 mm Diameter Approx. 0.515 mm Insulation Material HDPE Average Thickness 0.2 mm Diameter 0.915 ± 0.05 mm Twisted Four pairs Assembly Arranged in accordance with the structure figure. Jacket Material PVC or LSOH Average Thickness 0.5 mm Diameter 5.2 ± 0.2 mm 3. Electrical Characteristics: Comply with TIA/EIA-568-B.2 Standard. Item Electrical Characteristics of Cable Impedance ( 1 – 100 MHz) 100 ± 15 Ω Conductor Resistance (20℃) 9.38 Ω Per 100 m (328 ft) Resistance Unbalance (20℃) Max. 5% Insulation Resistance (20℃) 1500MW - Km DC 500V (Between wire and ground) Dielectric strength DC 500V / 1min. or AC 350 V / 1min. Mutual Capacitance (1KHz) Max. 5.6 nF Per 100 m (328 ft) Capacitance unbalance (1KHz) 330 pF Per 100 m (328 ft) ( pair to ground) Delay Skew Max. 45 ns Per 100 m (328 ft) Frequency Insertion Loss (dB/100m) Max. Propagation Delay 0.772MHz 1.8 — 1 MHz 2.0 534 + 36/ √f (f：MHz) 4 MHz 4.1 8 MHz 5.8 10 MHz 6.5 16 MHz 8.2 20 MHz 9.3 25 MHz 10.4 31.25 MHz 11.7 62.5 MHz 17.0 100 MHz 22.0 Frequency NEXT (dB/100m) Min. PSNEXT (dB/100m) Min. ELFXT (dB/100m) Min. PSELFXT (dB/100m) Min. 0.772MHz 67.0 64.0 — — 1 MHz 65.3 62.3 63.8 60.8 4 MHz 56.3 53.3 51.7 48.7 8 MHz 51.8 48.8 45.7 42.7 10 MHz 50.3 47.3 43.8 40.8 16 MHz 47.3 44.4 39.7 36.7 20 MHz 45.8 42.8 37.7 34.7 25 MHz 44.3 41.3 35.8 32.8 31.25 MHz 42.9 39.9 33.9 30.9 62.5 MHz 36.4 35.4 27.8 24.6 100 MHz 35.3 32.3 23.8 20.8 Return Loss (dB/100m) 1≦ f ＜10MHz RL≧ 20+5.0 log(f) 10≦ f ＜20MHz RL≧ 25 20≦ f ＜100MHz RL≧ 25-7.0 log(f/20) 4. Packing: 305 Meters / Reel (8 type) in a box.
-
CAT6-UTP-4P
LAN CABLE is suitable for data transmission on Local Area Network , especially for computer, video or perfect audio. Specifications Application — AS Connecting media of Work Area Outlet to PCs, terminals, workstations and data equipments — Supporting 1000 Base - T Gigabit Ethernet, 550MHz Broadband video and 155 / 622 Mbps ATM with channel performance extended to 250MHz Configration — 24AWG solid copper for Horizontal cable — 24AWG stranded copper for patch cable — 4 pairs — Central Spacer — PVC/LSNH FRPE jacket — Packed with special designed paper reels and cartons Standards — TIA / EIA 568 - B2 - 1 — ISO / IEC - 11801 — CENELEC EN 50173 — CENELEC EN 50288 - 6 (for unscreened cable) — UL Subj. 444 — CSA C 22.2 NO. 214 Qualifications — Verified to TIA / EIA 568 - B.2 Category 6 by UL / CSA & ETL — Verified to TIA / EIA 568 - B.2 Category 6 by 3P Third Party Testing — Verified to ISO / IEC 11801 Category 6 by UL / CSA — UL / CSA & ETL approved CM / CMR Electrical Properties Charts Characteristic Impedance Attenuation ELFEXT (P-P) ELFEXT (PS) Delay NEXT (P-P) NEXT (PS) Return Loss Skew